Mechanisms

Crank

Print

Crank

Steps 1 2 3 4 5 6 7 8 9 10 11 12

Crank

((vim videoid=dhhy66gmi6 wl=0))
((img class=img-responsive src=https://learn.birdbraintechnologies.com/wp-content/uploads/2018/10/Screenshot-2018-12-10-10.45.18-768x429.png))

Build a crank mechanism with the Hummingbird Robotics Kit! A crank transfers the servo’s rotation motion into a swinging pivot motion, like a door.

Popular uses of the crank mechanism include moving mouths and swinging doors. What will you create?

Build Time: 30-60 min (depending on skill level and design choice)

((img class=img-responsive src=https://learn.birdbraintechnologies.com/wp-content/uploads/2018/10/Crank_Step-2._STILL-768x432.jpg))

Hummingbird Robotics Kit Hardware*

  • Hummingbird Controller (Bit Controller pictured. The Duo controller will also work)
  • Battery Pack or AC Plug
  • Position Servo (Your servo may look different)
  • Circular Servo Horn (Black for Hummingbird Bit and white for Duo)

*All of these parts are included in any Hummingbird Robotics Kit

Suggested Craft Supplies

This page contains affiliate links. If you use these links to make a purchase we may earn a commission at no extra cost to you.

((vim videoid=imc8xdtj3p wl=1))
((img class=img-responsive src=https://learn.birdbraintechnologies.com/wp-content/uploads/2018/10/Screenshot-2019-04-30-11.04.232-768x432.png))

Interlock the tabs on one side of the box.

((vim videoid=qjjw9k0avf wl=1))
((img class=img-responsive src=https://learn.birdbraintechnologies.com/wp-content/uploads/2018/10/Screenshot-2019-04-30-11.04.45-768x415.png))

Cut a small section (about 2 cm by 5cm) from the piece of scrap cardboard.

((vim videoid=05pwka5xzy wl=1))
((img class=img-responsive src=https://learn.birdbraintechnologies.com/wp-content/uploads/2018/10/Screenshot-2019-04-30-11.05.08-768x425.png))

Unbend the paperclip into an L shape with a small hook on the top.

Place the L- shaped paperclip inside the box. The shorter arm of the L- shaped paperclip should be be centered on the lower flap of the cardboard box.

((vim videoid=btm8pb9e0d wl=1))
((img class=img-responsive src=https://learn.birdbraintechnologies.com/wp-content/uploads/2018/10/Screenshot-2019-04-30-11.05.32-768x417.png))

Place a generous amount of hot glue over the shorter arm of the paperclip, then place the small cardboard section over the glue. You’ve just create a linkage point for your crank.

((vim videoid=r45bgjizhq wl=1))
((img class=img-responsive src=https://learn.birdbraintechnologies.com/wp-content/uploads/2018/10/Screenshot-2019-04-30-10.34.25-768x427.png))

Cut off another section of scrap cardboard. This section should be about 7 cm in length and it should match the width of the circular servo horn.

((vim videoid=cndxotcfo2 wl=1))
((img class=img-responsive src=https://learn.birdbraintechnologies.com/wp-content/uploads/2018/10/Screenshot-2019-04-30-10.35.55-768x427.png))

Glue the servo horn onto the one end of the cardboard scrap. Try not to get hot glue into the center hole of the servo horn.

((vim videoid=25g5muj543 wl=1))
((img class=img-responsive src=https://learn.birdbraintechnologies.com/wp-content/uploads/2018/10/Screenshot-2019-04-30-11.06.29-768x419.png))

Trim the excess cardboard around the edge of the servo horn.

((vim videoid=1abbjxj450 wl=1))
((img class=img-responsive src=https://learn.birdbraintechnologies.com/wp-content/uploads/2018/10/Screenshot-2019-04-30-11.09.56-768x419.png))

Push the servo horn onto the servo shaft. This servo will rotate 180 degrees. If you imagine the servo as a clock, with the wire side indicating the top of the clock, align the servo horn so that the arm can swing freely between 6 o’clock and 12 o’clock.

If you are using the HS-311 servo from the Hummingbird Duo kit, your servo will need to swing in the opposite direction.

((vim videoid=afyeh8yzbo wl=1))
((img class=img-responsive src=https://learn.birdbraintechnologies.com/wp-content/uploads/2018/10/Screenshot-2019-04-30-11.11.00-768x419.png))

Cut about 2cm of the cardboard arm. Using a blade, poke a hole through the end of the cardboard arm.

((vim videoid=ry9cdmam69 wl=1))
((img class=img-responsive src=https://learn.birdbraintechnologies.com/wp-content/uploads/2018/10/Screenshot-2018-12-10-10.43.55-768x427.png))

Feed the hook end of the L- shaped paperclip through the hole at the end of the cardboard arm. Make sure the wired side of the servo is pointed into the box. Use a generous amount of glue to secure the servo to the floor of the box.

If you are using the HS-311 servo from the Hummingbird Duo kit, your servo will need to be pointed in the opposite direction, with the wired pointed out of the box. In addition, you will need to place a couple of pieces of cardboard under the servo to raise it so that the servo horn does not touch the bottom of the box.

Need help getting started? Select your desired programming language and device from this page.

Back to Top